Can I re-format OS X drive without removing it from my MacBook Pro?
I've got a mid 2012 MacBook Pro (non-retina) with a removable HD (Machine A). I want to perform a clean install of OS X El Capitan 10.11 on the HD, for which I have an install USB stick made.
Normally to do this I would:
Remove the HD from the Machine A.
Put it in a HD enclosure.
Plug the HD enclosure into another machine (Machine B).
Run disk utility on Machine B to wipe the HD in the enclosure.
Take the HD out of the enclosure and put it back into Machine A.
Boot machine A into my installer USB and install OS X 10.11 from there.
I don't have a HD enclosure at hand and wondered if I can instead:
Turn-off machine A.
Link machine B and machine A by cable. (What cable spec?)
Run disk utility on machine B to reformat the drive on Machine A.
Perform task 6 from above.
Would that work? What cable should I use?
hard-drive external-disk
edited Dec 8 at 17:40
Nimesh Neema
14.4k43871
asked Dec 8 at 16:57
sam
1,126103158
add a comment |
I've got a mid 2012 MacBook Pro (non-retina) with a removable HD (Machine A). I want to perform a clean install of OS X El Capitan 10.11 on the HD, for which I have an install USB stick made.
Normally to do this I would:
Remove the HD from the Machine A.
Put it in a HD enclosure.
Plug the HD enclosure into another machine (Machine B).
Run disk utility on Machine B to wipe the HD in the enclosure.
Take the HD out of the enclosure and put it back into Machine A.
Boot machine A into my installer USB and install OS X 10.11 from there.
I don't have a HD enclosure at hand and wondered if I can instead:
Turn-off machine A.
Link machine B and machine A by cable. (What cable spec?)
Run disk utility on machine B to reformat the drive on Machine A.
Perform task 6 from above.
Would that work? What cable should I use?
hard-drive external-disk
edited Dec 8 at 17:40
Nimesh Neema
14.4k43871
asked Dec 8 at 16:57
sam
1,126103158
add a comment |
I've got a mid 2012 MacBook Pro (non-retina) with a removable HD (Machine A). I want to perform a clean install of OS X El Capitan 10.11 on the HD, for which I have an install USB stick made.
Normally to do this I would:
Remove the HD from the Machine A.
Put it in a HD enclosure.
Plug the HD enclosure into another machine (Machine B).
Run disk utility on Machine B to wipe the HD in the enclosure.
Take the HD out of the enclosure and put it back into Machine A.
Boot machine A into my installer USB and install OS X 10.11 from there.
I don't have a HD enclosure at hand and wondered if I can instead:
Turn-off machine A.
Link machine B and machine A by cable. (What cable spec?)
Run disk utility on machine B to reformat the drive on Machine A.
Perform task 6 from above.
Would that work? What cable should I use?
hard-drive external-disk
edited Dec 8 at 17:40
Nimesh Neema
14.4k43871
asked Dec 8 at 16:57
sam
1,126103158
I've got a mid 2012 MacBook Pro (non-retina) with a removable HD (Machine A). I want to perform a clean install of OS X El Capitan 10.11 on the HD, for which I have an install USB stick made.
Normally to do this I would:
Remove the HD from the Machine A.
Put it in a HD enclosure.
Plug the HD enclosure into another machine (Machine B).
Run disk utility on Machine B to wipe the HD in the enclosure.
Take the HD out of the enclosure and put it back into Machine A.
Boot machine A into my installer USB and install OS X 10.11 from there.
I don't have a HD enclosure at hand and wondered if I can instead:
Turn-off machine A.
Link machine B and machine A by cable. (What cable spec?)
Run disk utility on machine B to reformat the drive on Machine A.
Perform task 6 from above.
Would that work? What cable should I use?
hard-drive external-disk
hard-drive external-disk
edited Dec 8 at 17:40
Nimesh Neema
14.4k43871
asked Dec 8 at 16:57
sam
1,126103158
edited Dec 8 at 17:40
Nimesh Neema
14.4k43871
asked Dec 8 at 16:57
sam
1,126103158
edited Dec 8 at 17:40
Nimesh Neema
14.4k43871
edited Dec 8 at 17:40
Nimesh Neema
14.4k43871
edited Dec 8 at 17:40
Nimesh Neema
14.4k43871
14.4k43871
asked Dec 8 at 16:57
sam
1,126103158
asked Dec 8 at 16:57
sam
1,126103158
asked Dec 8 at 16:57
sam
1,126103158
1,126103158
add a comment |
add a comment |
4 Answers
4
active
oldest
votes
You don’t need to remove the HDD and no need for second Mac.
Boot the MacBook Pro from the USB stick (that you made with OS X El Capitan 10.11)
Using Disk Utilities in the Tools menu, you can reformat the hard drive as part of the installation process.
To boot using the USB, restart your MacBook and press and hold the Option key and Select the USB drive to boot.
Note: you are operating (using OS X) from the USB
edited Dec 8 at 18:50
Allan
42k1360154
answered Dec 8 at 17:15
Mike Scott
8,87822530
3
Just be aware that running MacOS from a USB is sloooow. But it works just fine.
– gnasher729
Dec 9 at 13:52
USB 2 sticks are always slow. USB 3 is quite a bit better.
– Dev
Dec 10 at 3:47
add a comment |
There is no need for the USB stick, you can do a clean install from the recovery partition if it's available. Depending on the origin of the USB stick, it might even be a bad idea to use it at all.
Restart into recovery mode, delete the current installation and reinstall the operating system for the same result: https://support.apple.com/en-us/HT204904
answered Dec 8 at 18:46
John Keates
2,033410
3
Yes, while it is true one can use install from the recovery partition without a USB nonetheless, the User wants to install OS X El Capitan and the Mid 2012 MacBook Pro (non-Retina) shipped with Mac OS X 10.7.4 not OS X 10.11 and as such he cannot easily directly install OS X El Capitan 10.11 without using the USB Installer he already has that has OS X El Capitan 10.11 already on it. Using his existing USB Installer is the best and most recommended way to go under the circumstances!
– user3439894
Dec 8 at 19:09
That is possible by using Internet Recovery, this installs the shipped OS. This 2012 model might have it.
– John Keates
Dec 8 at 19:10
@JohnKeates A 2012 MacBook Pro can’t possibly have shipped with El Capitan, which was released in September 2015.
– Mike Scott
Dec 8 at 20:27
@MikeScott I guess John means the 2012 model has Internet Recovery. “[installing OS X 10.11] is possible using IR, [recovery partition] installs the shipped OS”.
– 11684
Dec 8 at 23:33
1
The OP already has already created a USB Installer with OS X El Capitan on it and it is senseless to not use it as one would then have to download another +5 GB, which depending on the bandwidth could take may hours. Not everyone has high bandwidth from their ISP. Yes while technically it can be done without using a USB Installer nonetheless it makes absolutely no sense whatsoever to do it any other way then using the already existing USB Installer with OS X El Capitan on it!
– user3439894
Dec 9 at 12:38
add a comment |
Can I re-format OS X drive without removing it from my MacBook Pro?
Yes.
You need not remove the hard drive from machine A or connect machine A to machine B to do this.
You simply need a bootable (USB) installer for OS X El Capitan 10.11. Once you have the bootable installer handy, simply leave the hard disk into machine A, plug-in the bootable USB installer, and boot off it.
Once booted, simply start Disk utility, erase the hard drive and perform fresh install of OS X El Capitan 10.11 on it.
You can find the instructions to create a bootable installer for OS X El Capitan 10.11 here:
- How to create a bootable installer for macOS
To boot from the USB, simply restart your MacBook Pro with the installer USB drive plugged-in, and press & hold the Option key. You'll be prompted to select the boot media. Select the USB drive to boot.
For detailed instructions, refer to the Use Startup Manager section in the Apple Support article, How to select a different startup disk.
answered Dec 8 at 17:16
Nimesh Neema
14.4k43871
add a comment |
The other answers describe the simplest and most straightforward way to do this.
However, for the sake of completeness, consider target disk mode.
Target disk mode allows you to boot your Mac into a state where it presents itself to other Macs as an external HD.
First, connect the two computers together with either USB C, Thunderbolt, or Firewire.
Then, on the target computer, restart while holding down the T key.
The target Mac will boot to a screen with a Thunderbolt or Firewire symbol.
It should appear as an external HD on the connected Mac.
See this Apple support article for many more details.
answered Dec 9 at 5:48
daviewales
1,094721
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "118"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fapple.stackexchange.com%2fquestions%2f345070%2fcan-i-re-format-os-x-drive-without-removing-it-from-my-macbook-pro%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
4 Answers
4
active
oldest
votes
4 Answers
4
active
oldest
votes
active
oldest
votes
active
oldest
votes
You don’t need to remove the HDD and no need for second Mac.
Boot the MacBook Pro from the USB stick (that you made with OS X El Capitan 10.11)
Using Disk Utilities in the Tools menu, you can reformat the hard drive as part of the installation process.
To boot using the USB, restart your MacBook and press and hold the Option key and Select the USB drive to boot.
Note: you are operating (using OS X) from the USB
edited Dec 8 at 18:50
Allan
42k1360154
answered Dec 8 at 17:15
Mike Scott
8,87822530
3
Just be aware that running MacOS from a USB is sloooow. But it works just fine.
– gnasher729
Dec 9 at 13:52
USB 2 sticks are always slow. USB 3 is quite a bit better.
– Dev
Dec 10 at 3:47
add a comment |
You don’t need to remove the HDD and no need for second Mac.
Boot the MacBook Pro from the USB stick (that you made with OS X El Capitan 10.11)
Using Disk Utilities in the Tools menu, you can reformat the hard drive as part of the installation process.
To boot using the USB, restart your MacBook and press and hold the Option key and Select the USB drive to boot.
Note: you are operating (using OS X) from the USB
edited Dec 8 at 18:50
Allan
42k1360154
answered Dec 8 at 17:15
Mike Scott
8,87822530
3
Just be aware that running MacOS from a USB is sloooow. But it works just fine.
– gnasher729
Dec 9 at 13:52
USB 2 sticks are always slow. USB 3 is quite a bit better.
– Dev
Dec 10 at 3:47
add a comment |
You don’t need to remove the HDD and no need for second Mac.
Boot the MacBook Pro from the USB stick (that you made with OS X El Capitan 10.11)
Using Disk Utilities in the Tools menu, you can reformat the hard drive as part of the installation process.
To boot using the USB, restart your MacBook and press and hold the Option key and Select the USB drive to boot.
Note: you are operating (using OS X) from the USB
edited Dec 8 at 18:50
Allan
42k1360154
answered Dec 8 at 17:15
Mike Scott
8,87822530
You don’t need to remove the HDD and no need for second Mac.
Boot the MacBook Pro from the USB stick (that you made with OS X El Capitan 10.11)
Using Disk Utilities in the Tools menu, you can reformat the hard drive as part of the installation process.
To boot using the USB, restart your MacBook and press and hold the Option key and Select the USB drive to boot.
Note: you are operating (using OS X) from the USB
edited Dec 8 at 18:50
Allan
42k1360154
answered Dec 8 at 17:15
Mike Scott
8,87822530
edited Dec 8 at 18:50
Allan
42k1360154
edited Dec 8 at 18:50
Allan
42k1360154
edited Dec 8 at 18:50
Allan
42k1360154
42k1360154
answered Dec 8 at 17:15
Mike Scott
8,87822530
answered Dec 8 at 17:15
Mike Scott
8,87822530
answered Dec 8 at 17:15
Mike Scott
8,87822530
8,87822530
3
Just be aware that running MacOS from a USB is sloooow. But it works just fine.
– gnasher729
Dec 9 at 13:52
USB 2 sticks are always slow. USB 3 is quite a bit better.
– Dev
Dec 10 at 3:47
add a comment |
3
Just be aware that running MacOS from a USB is sloooow. But it works just fine.
– gnasher729
Dec 9 at 13:52
USB 2 sticks are always slow. USB 3 is quite a bit better.
– Dev
Dec 10 at 3:47
3
3
Just be aware that running MacOS from a USB is sloooow. But it works just fine.
– gnasher729
Dec 9 at 13:52
Just be aware that running MacOS from a USB is sloooow. But it works just fine.
– gnasher729
Dec 9 at 13:52
USB 2 sticks are always slow. USB 3 is quite a bit better.
– Dev
Dec 10 at 3:47
USB 2 sticks are always slow. USB 3 is quite a bit better.
– Dev
Dec 10 at 3:47
add a comment |
There is no need for the USB stick, you can do a clean install from the recovery partition if it's available. Depending on the origin of the USB stick, it might even be a bad idea to use it at all.
Restart into recovery mode, delete the current installation and reinstall the operating system for the same result: https://support.apple.com/en-us/HT204904
answered Dec 8 at 18:46
John Keates
2,033410
3
Yes, while it is true one can use install from the recovery partition without a USB nonetheless, the User wants to install OS X El Capitan and the Mid 2012 MacBook Pro (non-Retina) shipped with Mac OS X 10.7.4 not OS X 10.11 and as such he cannot easily directly install OS X El Capitan 10.11 without using the USB Installer he already has that has OS X El Capitan 10.11 already on it. Using his existing USB Installer is the best and most recommended way to go under the circumstances!
– user3439894
Dec 8 at 19:09
That is possible by using Internet Recovery, this installs the shipped OS. This 2012 model might have it.
– John Keates
Dec 8 at 19:10
@JohnKeates A 2012 MacBook Pro can’t possibly have shipped with El Capitan, which was released in September 2015.
– Mike Scott
Dec 8 at 20:27
@MikeScott I guess John means the 2012 model has Internet Recovery. “[installing OS X 10.11] is possible using IR, [recovery partition] installs the shipped OS”.
– 11684
Dec 8 at 23:33
1
The OP already has already created a USB Installer with OS X El Capitan on it and it is senseless to not use it as one would then have to download another +5 GB, which depending on the bandwidth could take may hours. Not everyone has high bandwidth from their ISP. Yes while technically it can be done without using a USB Installer nonetheless it makes absolutely no sense whatsoever to do it any other way then using the already existing USB Installer with OS X El Capitan on it!
– user3439894
Dec 9 at 12:38
add a comment |
There is no need for the USB stick, you can do a clean install from the recovery partition if it's available. Depending on the origin of the USB stick, it might even be a bad idea to use it at all.
Restart into recovery mode, delete the current installation and reinstall the operating system for the same result: https://support.apple.com/en-us/HT204904
answered Dec 8 at 18:46
John Keates
2,033410
3
Yes, while it is true one can use install from the recovery partition without a USB nonetheless, the User wants to install OS X El Capitan and the Mid 2012 MacBook Pro (non-Retina) shipped with Mac OS X 10.7.4 not OS X 10.11 and as such he cannot easily directly install OS X El Capitan 10.11 without using the USB Installer he already has that has OS X El Capitan 10.11 already on it. Using his existing USB Installer is the best and most recommended way to go under the circumstances!
– user3439894
Dec 8 at 19:09
That is possible by using Internet Recovery, this installs the shipped OS. This 2012 model might have it.
– John Keates
Dec 8 at 19:10
@JohnKeates A 2012 MacBook Pro can’t possibly have shipped with El Capitan, which was released in September 2015.
– Mike Scott
Dec 8 at 20:27
@MikeScott I guess John means the 2012 model has Internet Recovery. “[installing OS X 10.11] is possible using IR, [recovery partition] installs the shipped OS”.
– 11684
Dec 8 at 23:33
1
The OP already has already created a USB Installer with OS X El Capitan on it and it is senseless to not use it as one would then have to download another +5 GB, which depending on the bandwidth could take may hours. Not everyone has high bandwidth from their ISP. Yes while technically it can be done without using a USB Installer nonetheless it makes absolutely no sense whatsoever to do it any other way then using the already existing USB Installer with OS X El Capitan on it!
– user3439894
Dec 9 at 12:38
add a comment |
There is no need for the USB stick, you can do a clean install from the recovery partition if it's available. Depending on the origin of the USB stick, it might even be a bad idea to use it at all.
Restart into recovery mode, delete the current installation and reinstall the operating system for the same result: https://support.apple.com/en-us/HT204904
answered Dec 8 at 18:46
John Keates
2,033410
There is no need for the USB stick, you can do a clean install from the recovery partition if it's available. Depending on the origin of the USB stick, it might even be a bad idea to use it at all.
Restart into recovery mode, delete the current installation and reinstall the operating system for the same result: https://support.apple.com/en-us/HT204904
answered Dec 8 at 18:46
John Keates
2,033410
answered Dec 8 at 18:46
John Keates
2,033410
answered Dec 8 at 18:46
John Keates
2,033410
answered Dec 8 at 18:46
John Keates
2,033410
2,033410
3
Yes, while it is true one can use install from the recovery partition without a USB nonetheless, the User wants to install OS X El Capitan and the Mid 2012 MacBook Pro (non-Retina) shipped with Mac OS X 10.7.4 not OS X 10.11 and as such he cannot easily directly install OS X El Capitan 10.11 without using the USB Installer he already has that has OS X El Capitan 10.11 already on it. Using his existing USB Installer is the best and most recommended way to go under the circumstances!
– user3439894
Dec 8 at 19:09
That is possible by using Internet Recovery, this installs the shipped OS. This 2012 model might have it.
– John Keates
Dec 8 at 19:10
@JohnKeates A 2012 MacBook Pro can’t possibly have shipped with El Capitan, which was released in September 2015.
– Mike Scott
Dec 8 at 20:27
@MikeScott I guess John means the 2012 model has Internet Recovery. “[installing OS X 10.11] is possible using IR, [recovery partition] installs the shipped OS”.
– 11684
Dec 8 at 23:33
1
The OP already has already created a USB Installer with OS X El Capitan on it and it is senseless to not use it as one would then have to download another +5 GB, which depending on the bandwidth could take may hours. Not everyone has high bandwidth from their ISP. Yes while technically it can be done without using a USB Installer nonetheless it makes absolutely no sense whatsoever to do it any other way then using the already existing USB Installer with OS X El Capitan on it!
– user3439894
Dec 9 at 12:38
add a comment |
3
Yes, while it is true one can use install from the recovery partition without a USB nonetheless, the User wants to install OS X El Capitan and the Mid 2012 MacBook Pro (non-Retina) shipped with Mac OS X 10.7.4 not OS X 10.11 and as such he cannot easily directly install OS X El Capitan 10.11 without using the USB Installer he already has that has OS X El Capitan 10.11 already on it. Using his existing USB Installer is the best and most recommended way to go under the circumstances!
– user3439894
Dec 8 at 19:09
That is possible by using Internet Recovery, this installs the shipped OS. This 2012 model might have it.
– John Keates
Dec 8 at 19:10
@JohnKeates A 2012 MacBook Pro can’t possibly have shipped with El Capitan, which was released in September 2015.
– Mike Scott
Dec 8 at 20:27
@MikeScott I guess John means the 2012 model has Internet Recovery. “[installing OS X 10.11] is possible using IR, [recovery partition] installs the shipped OS”.
– 11684
Dec 8 at 23:33
1
The OP already has already created a USB Installer with OS X El Capitan on it and it is senseless to not use it as one would then have to download another +5 GB, which depending on the bandwidth could take may hours. Not everyone has high bandwidth from their ISP. Yes while technically it can be done without using a USB Installer nonetheless it makes absolutely no sense whatsoever to do it any other way then using the already existing USB Installer with OS X El Capitan on it!
– user3439894
Dec 9 at 12:38
3
3
Yes, while it is true one can use install from the recovery partition without a USB nonetheless, the User wants to install OS X El Capitan and the Mid 2012 MacBook Pro (non-Retina) shipped with Mac OS X 10.7.4 not OS X 10.11 and as such he cannot easily directly install OS X El Capitan 10.11 without using the USB Installer he already has that has OS X El Capitan 10.11 already on it. Using his existing USB Installer is the best and most recommended way to go under the circumstances!
– user3439894
Dec 8 at 19:09
Yes, while it is true one can use install from the recovery partition without a USB nonetheless, the User wants to install OS X El Capitan and the Mid 2012 MacBook Pro (non-Retina) shipped with Mac OS X 10.7.4 not OS X 10.11 and as such he cannot easily directly install OS X El Capitan 10.11 without using the USB Installer he already has that has OS X El Capitan 10.11 already on it. Using his existing USB Installer is the best and most recommended way to go under the circumstances!
– user3439894
Dec 8 at 19:09
That is possible by using Internet Recovery, this installs the shipped OS. This 2012 model might have it.
– John Keates
Dec 8 at 19:10
That is possible by using Internet Recovery, this installs the shipped OS. This 2012 model might have it.
– John Keates
Dec 8 at 19:10
@JohnKeates A 2012 MacBook Pro can’t possibly have shipped with El Capitan, which was released in September 2015.
– Mike Scott
Dec 8 at 20:27
@JohnKeates A 2012 MacBook Pro can’t possibly have shipped with El Capitan, which was released in September 2015.
– Mike Scott
Dec 8 at 20:27
@MikeScott I guess John means the 2012 model has Internet Recovery. “[installing OS X 10.11] is possible using IR, [recovery partition] installs the shipped OS”.
– 11684
Dec 8 at 23:33
@MikeScott I guess John means the 2012 model has Internet Recovery. “[installing OS X 10.11] is possible using IR, [recovery partition] installs the shipped OS”.
– 11684
Dec 8 at 23:33
1
1
The OP already has already created a USB Installer with OS X El Capitan on it and it is senseless to not use it as one would then have to download another +5 GB, which depending on the bandwidth could take may hours. Not everyone has high bandwidth from their ISP. Yes while technically it can be done without using a USB Installer nonetheless it makes absolutely no sense whatsoever to do it any other way then using the already existing USB Installer with OS X El Capitan on it!
– user3439894
Dec 9 at 12:38
The OP already has already created a USB Installer with OS X El Capitan on it and it is senseless to not use it as one would then have to download another +5 GB, which depending on the bandwidth could take may hours. Not everyone has high bandwidth from their ISP. Yes while technically it can be done without using a USB Installer nonetheless it makes absolutely no sense whatsoever to do it any other way then using the already existing USB Installer with OS X El Capitan on it!
– user3439894
Dec 9 at 12:38
add a comment |
Can I re-format OS X drive without removing it from my MacBook Pro?
Yes.
You need not remove the hard drive from machine A or connect machine A to machine B to do this.
You simply need a bootable (USB) installer for OS X El Capitan 10.11. Once you have the bootable installer handy, simply leave the hard disk into machine A, plug-in the bootable USB installer, and boot off it.
Once booted, simply start Disk utility, erase the hard drive and perform fresh install of OS X El Capitan 10.11 on it.
You can find the instructions to create a bootable installer for OS X El Capitan 10.11 here:
- How to create a bootable installer for macOS
To boot from the USB, simply restart your MacBook Pro with the installer USB drive plugged-in, and press & hold the Option key. You'll be prompted to select the boot media. Select the USB drive to boot.
For detailed instructions, refer to the Use Startup Manager section in the Apple Support article, How to select a different startup disk.
answered Dec 8 at 17:16
Nimesh Neema
14.4k43871
add a comment |
Can I re-format OS X drive without removing it from my MacBook Pro?
Yes.
You need not remove the hard drive from machine A or connect machine A to machine B to do this.
You simply need a bootable (USB) installer for OS X El Capitan 10.11. Once you have the bootable installer handy, simply leave the hard disk into machine A, plug-in the bootable USB installer, and boot off it.
Once booted, simply start Disk utility, erase the hard drive and perform fresh install of OS X El Capitan 10.11 on it.
You can find the instructions to create a bootable installer for OS X El Capitan 10.11 here:
- How to create a bootable installer for macOS
To boot from the USB, simply restart your MacBook Pro with the installer USB drive plugged-in, and press & hold the Option key. You'll be prompted to select the boot media. Select the USB drive to boot.
For detailed instructions, refer to the Use Startup Manager section in the Apple Support article, How to select a different startup disk.
answered Dec 8 at 17:16
Nimesh Neema
14.4k43871
add a comment |
Can I re-format OS X drive without removing it from my MacBook Pro?
Yes.
You need not remove the hard drive from machine A or connect machine A to machine B to do this.
You simply need a bootable (USB) installer for OS X El Capitan 10.11. Once you have the bootable installer handy, simply leave the hard disk into machine A, plug-in the bootable USB installer, and boot off it.
Once booted, simply start Disk utility, erase the hard drive and perform fresh install of OS X El Capitan 10.11 on it.
You can find the instructions to create a bootable installer for OS X El Capitan 10.11 here:
- How to create a bootable installer for macOS
To boot from the USB, simply restart your MacBook Pro with the installer USB drive plugged-in, and press & hold the Option key. You'll be prompted to select the boot media. Select the USB drive to boot.
For detailed instructions, refer to the Use Startup Manager section in the Apple Support article, How to select a different startup disk.
answered Dec 8 at 17:16
Nimesh Neema
14.4k43871
Can I re-format OS X drive without removing it from my MacBook Pro?
Yes.
You need not remove the hard drive from machine A or connect machine A to machine B to do this.
You simply need a bootable (USB) installer for OS X El Capitan 10.11. Once you have the bootable installer handy, simply leave the hard disk into machine A, plug-in the bootable USB installer, and boot off it.
Once booted, simply start Disk utility, erase the hard drive and perform fresh install of OS X El Capitan 10.11 on it.
You can find the instructions to create a bootable installer for OS X El Capitan 10.11 here:
- How to create a bootable installer for macOS
To boot from the USB, simply restart your MacBook Pro with the installer USB drive plugged-in, and press & hold the Option key. You'll be prompted to select the boot media. Select the USB drive to boot.
For detailed instructions, refer to the Use Startup Manager section in the Apple Support article, How to select a different startup disk.
answered Dec 8 at 17:16
Nimesh Neema
14.4k43871
edited Dec 8 at 17:55
answered Dec 8 at 17:16
Nimesh Neema
14.4k43871
answered Dec 8 at 17:16
Nimesh Neema
14.4k43871
answered Dec 8 at 17:16
Nimesh Neema
14.4k43871
14.4k43871
add a comment |
add a comment |
The other answers describe the simplest and most straightforward way to do this.
However, for the sake of completeness, consider target disk mode.
Target disk mode allows you to boot your Mac into a state where it presents itself to other Macs as an external HD.
First, connect the two computers together with either USB C, Thunderbolt, or Firewire.
Then, on the target computer, restart while holding down the T key.
The target Mac will boot to a screen with a Thunderbolt or Firewire symbol.
It should appear as an external HD on the connected Mac.
See this Apple support article for many more details.
answered Dec 9 at 5:48
daviewales
1,094721
add a comment |
The other answers describe the simplest and most straightforward way to do this.
However, for the sake of completeness, consider target disk mode.
Target disk mode allows you to boot your Mac into a state where it presents itself to other Macs as an external HD.
First, connect the two computers together with either USB C, Thunderbolt, or Firewire.
Then, on the target computer, restart while holding down the T key.
The target Mac will boot to a screen with a Thunderbolt or Firewire symbol.
It should appear as an external HD on the connected Mac.
See this Apple support article for many more details.
answered Dec 9 at 5:48
daviewales
1,094721
add a comment |
The other answers describe the simplest and most straightforward way to do this.
However, for the sake of completeness, consider target disk mode.
Target disk mode allows you to boot your Mac into a state where it presents itself to other Macs as an external HD.
First, connect the two computers together with either USB C, Thunderbolt, or Firewire.
Then, on the target computer, restart while holding down the T key.
The target Mac will boot to a screen with a Thunderbolt or Firewire symbol.
It should appear as an external HD on the connected Mac.
See this Apple support article for many more details.
answered Dec 9 at 5:48
daviewales
1,094721
The other answers describe the simplest and most straightforward way to do this.
However, for the sake of completeness, consider target disk mode.
Target disk mode allows you to boot your Mac into a state where it presents itself to other Macs as an external HD.
First, connect the two computers together with either USB C, Thunderbolt, or Firewire.
Then, on the target computer, restart while holding down the T key.
The target Mac will boot to a screen with a Thunderbolt or Firewire symbol.
It should appear as an external HD on the connected Mac.
See this Apple support article for many more details.
answered Dec 9 at 5:48
daviewales
1,094721
answered Dec 9 at 5:48
daviewales
1,094721
answered Dec 9 at 5:48
daviewales
1,094721
answered Dec 9 at 5:48
daviewales
1,094721
1,094721
add a comment |
add a comment |
Thanks for contributing an answer to Ask Different!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fapple.stackexchange.com%2fquestions%2f345070%2fcan-i-re-format-os-x-drive-without-removing-it-from-my-macbook-pro%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
