Cisco RV320 in router mode loses internet connectivity?
Cisco RV320 can work in either "Gateway" or "Router" mode.
Manual says the following about the "Router" mode
Choose this mode if the device is on a network with other routers
and another device is the network gateway to the Internet or this network is
not connected to the Internet. In Router mode, Internet connectivity is
available to the network devices only if you have another router that
functions as the Gateway. Since firewall protection is provided by the
gateway, disable this device firewall.
I connect WAN port of RV320 to LAN port of a cable modem. The modem works as gateway and router on 192.168.0.0. RV320 is on 192.168.1.0 and it shows that it got 192.168.0.13 from the modem. Modem does not show that address among connected devices however.
RV320 cannot ping any internet address while modem can. Any computer connected to RV320 gets valid IP and windows even shows that network has internet connection, but there actually isn't any. For some reason RV320 manages to resolve DNS names, however.
I tried disabling firewall, Ipv6 etc to no avail.
Am I missing something?
Is RV320 not able to work use another router with NAT as gateway?
What is "Router" mode for?
networking router
asked Mar 20 '15 at 6:49
Vaso
111
add a comment |
Cisco RV320 can work in either "Gateway" or "Router" mode.
Manual says the following about the "Router" mode
Choose this mode if the device is on a network with other routers
and another device is the network gateway to the Internet or this network is
not connected to the Internet. In Router mode, Internet connectivity is
available to the network devices only if you have another router that
functions as the Gateway. Since firewall protection is provided by the
gateway, disable this device firewall.
I connect WAN port of RV320 to LAN port of a cable modem. The modem works as gateway and router on 192.168.0.0. RV320 is on 192.168.1.0 and it shows that it got 192.168.0.13 from the modem. Modem does not show that address among connected devices however.
RV320 cannot ping any internet address while modem can. Any computer connected to RV320 gets valid IP and windows even shows that network has internet connection, but there actually isn't any. For some reason RV320 manages to resolve DNS names, however.
I tried disabling firewall, Ipv6 etc to no avail.
Am I missing something?
Is RV320 not able to work use another router with NAT as gateway?
What is "Router" mode for?
networking router
asked Mar 20 '15 at 6:49
Vaso
111
add a comment |
Cisco RV320 can work in either "Gateway" or "Router" mode.
Manual says the following about the "Router" mode
Choose this mode if the device is on a network with other routers
and another device is the network gateway to the Internet or this network is
not connected to the Internet. In Router mode, Internet connectivity is
available to the network devices only if you have another router that
functions as the Gateway. Since firewall protection is provided by the
gateway, disable this device firewall.
I connect WAN port of RV320 to LAN port of a cable modem. The modem works as gateway and router on 192.168.0.0. RV320 is on 192.168.1.0 and it shows that it got 192.168.0.13 from the modem. Modem does not show that address among connected devices however.
RV320 cannot ping any internet address while modem can. Any computer connected to RV320 gets valid IP and windows even shows that network has internet connection, but there actually isn't any. For some reason RV320 manages to resolve DNS names, however.
I tried disabling firewall, Ipv6 etc to no avail.
Am I missing something?
Is RV320 not able to work use another router with NAT as gateway?
What is "Router" mode for?
networking router
asked Mar 20 '15 at 6:49
Vaso
111
Cisco RV320 can work in either "Gateway" or "Router" mode.
Manual says the following about the "Router" mode
Choose this mode if the device is on a network with other routers
and another device is the network gateway to the Internet or this network is
not connected to the Internet. In Router mode, Internet connectivity is
available to the network devices only if you have another router that
functions as the Gateway. Since firewall protection is provided by the
gateway, disable this device firewall.
I connect WAN port of RV320 to LAN port of a cable modem. The modem works as gateway and router on 192.168.0.0. RV320 is on 192.168.1.0 and it shows that it got 192.168.0.13 from the modem. Modem does not show that address among connected devices however.
RV320 cannot ping any internet address while modem can. Any computer connected to RV320 gets valid IP and windows even shows that network has internet connection, but there actually isn't any. For some reason RV320 manages to resolve DNS names, however.
I tried disabling firewall, Ipv6 etc to no avail.
Am I missing something?
Is RV320 not able to work use another router with NAT as gateway?
What is "Router" mode for?
networking router
networking router
asked Mar 20 '15 at 6:49
Vaso
111
asked Mar 20 '15 at 6:49
Vaso
111
asked Mar 20 '15 at 6:49
Vaso
111
asked Mar 20 '15 at 6:49
Vaso
111
asked Mar 20 '15 at 6:49
Vaso
111
111
add a comment |
add a comment |
2 Answers
2
active
oldest
votes
Since simply turning router in "Gateway" mode instantly fixes internet connectivity,
on a network with other routers and another device is the network gateway to the Internet
probably means that there is gateway on the router subnet.
In my scenario the modem is on a different subnet, so RV320 must be set to Gateway mode. It's still strange that RV320 itself cannot ping internet addresses as it knows where WAN can be reached. Again, probably it looks for gateway on its own subnet.
answered Mar 20 '15 at 7:02
Vaso
111
add a comment |
In this cisco url, explain how to configure in gateway and router mode in cisco RV320
Basic:
The external cable (ISP) must be connected to the Internet WAN port and cable to your local network must be connected to any of the LAN ports (1,2,3,4)
Enter Cisco RV320 (192.168.1.1). (Change default credentials)
Enter "DHCP Setup" and select "Device IP Address" (default 192.168.1.1). Active "DHCP Server" and determine the range: "Range Start (Example 192.168.1.100)" and "Range End" (example 192.168.1.200) (note: don't use 192.168.1.1 or 192.168.1.255 into the range) and set "DNS Server/Use DNS as Bellow and set manually your DNS (example 8.8.8.8 8.8.4.4) and save the changes. Finally check "DHCP Status" ip leases your local network.
Enter a "system management" and select "Load Balance" (Auto Mode)
Enter "Setup/Network" and select "IPv4 Only" and "WAN Setting Table" should be "WAN1 (and WAN2) Obtain an IP automatically"
In "Setup / Advanced Routing" select "Gateway"
Note: Don't use "Router" because need to set routing table and RIP.
- Check "System Summary" that all information is correct
External links can break or be unavailable, in which case your answer would not be useful. Please include the essential information within your answer and use the link for attribution and further reading. Thanks.
– fixer1234
Aug 3 '16 at 21:55
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "3"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: true,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: 10,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fsuperuser.com%2fquestions%2f891764%2fcisco-rv320-in-router-mode-loses-internet-connectivity%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
Since simply turning router in "Gateway" mode instantly fixes internet connectivity,
on a network with other routers and another device is the network gateway to the Internet
probably means that there is gateway on the router subnet.
In my scenario the modem is on a different subnet, so RV320 must be set to Gateway mode. It's still strange that RV320 itself cannot ping internet addresses as it knows where WAN can be reached. Again, probably it looks for gateway on its own subnet.
answered Mar 20 '15 at 7:02
Vaso
111
add a comment |
Since simply turning router in "Gateway" mode instantly fixes internet connectivity,
on a network with other routers and another device is the network gateway to the Internet
probably means that there is gateway on the router subnet.
In my scenario the modem is on a different subnet, so RV320 must be set to Gateway mode. It's still strange that RV320 itself cannot ping internet addresses as it knows where WAN can be reached. Again, probably it looks for gateway on its own subnet.
answered Mar 20 '15 at 7:02
Vaso
111
add a comment |
Since simply turning router in "Gateway" mode instantly fixes internet connectivity,
on a network with other routers and another device is the network gateway to the Internet
probably means that there is gateway on the router subnet.
In my scenario the modem is on a different subnet, so RV320 must be set to Gateway mode. It's still strange that RV320 itself cannot ping internet addresses as it knows where WAN can be reached. Again, probably it looks for gateway on its own subnet.
answered Mar 20 '15 at 7:02
Vaso
111
Since simply turning router in "Gateway" mode instantly fixes internet connectivity,
on a network with other routers and another device is the network gateway to the Internet
probably means that there is gateway on the router subnet.
In my scenario the modem is on a different subnet, so RV320 must be set to Gateway mode. It's still strange that RV320 itself cannot ping internet addresses as it knows where WAN can be reached. Again, probably it looks for gateway on its own subnet.
answered Mar 20 '15 at 7:02
Vaso
111
answered Mar 20 '15 at 7:02
Vaso
111
answered Mar 20 '15 at 7:02
Vaso
111
answered Mar 20 '15 at 7:02
Vaso
111
111
add a comment |
add a comment |
In this cisco url, explain how to configure in gateway and router mode in cisco RV320
Basic:
The external cable (ISP) must be connected to the Internet WAN port and cable to your local network must be connected to any of the LAN ports (1,2,3,4)
Enter Cisco RV320 (192.168.1.1). (Change default credentials)
Enter "DHCP Setup" and select "Device IP Address" (default 192.168.1.1). Active "DHCP Server" and determine the range: "Range Start (Example 192.168.1.100)" and "Range End" (example 192.168.1.200) (note: don't use 192.168.1.1 or 192.168.1.255 into the range) and set "DNS Server/Use DNS as Bellow and set manually your DNS (example 8.8.8.8 8.8.4.4) and save the changes. Finally check "DHCP Status" ip leases your local network.
Enter a "system management" and select "Load Balance" (Auto Mode)
Enter "Setup/Network" and select "IPv4 Only" and "WAN Setting Table" should be "WAN1 (and WAN2) Obtain an IP automatically"
In "Setup / Advanced Routing" select "Gateway"
Note: Don't use "Router" because need to set routing table and RIP.
- Check "System Summary" that all information is correct
External links can break or be unavailable, in which case your answer would not be useful. Please include the essential information within your answer and use the link for attribution and further reading. Thanks.
– fixer1234
Aug 3 '16 at 21:55
add a comment |
In this cisco url, explain how to configure in gateway and router mode in cisco RV320
Basic:
The external cable (ISP) must be connected to the Internet WAN port and cable to your local network must be connected to any of the LAN ports (1,2,3,4)
Enter Cisco RV320 (192.168.1.1). (Change default credentials)
Enter "DHCP Setup" and select "Device IP Address" (default 192.168.1.1). Active "DHCP Server" and determine the range: "Range Start (Example 192.168.1.100)" and "Range End" (example 192.168.1.200) (note: don't use 192.168.1.1 or 192.168.1.255 into the range) and set "DNS Server/Use DNS as Bellow and set manually your DNS (example 8.8.8.8 8.8.4.4) and save the changes. Finally check "DHCP Status" ip leases your local network.
Enter a "system management" and select "Load Balance" (Auto Mode)
Enter "Setup/Network" and select "IPv4 Only" and "WAN Setting Table" should be "WAN1 (and WAN2) Obtain an IP automatically"
In "Setup / Advanced Routing" select "Gateway"
Note: Don't use "Router" because need to set routing table and RIP.
- Check "System Summary" that all information is correct
External links can break or be unavailable, in which case your answer would not be useful. Please include the essential information within your answer and use the link for attribution and further reading. Thanks.
– fixer1234
Aug 3 '16 at 21:55
add a comment |
In this cisco url, explain how to configure in gateway and router mode in cisco RV320
Basic:
The external cable (ISP) must be connected to the Internet WAN port and cable to your local network must be connected to any of the LAN ports (1,2,3,4)
Enter Cisco RV320 (192.168.1.1). (Change default credentials)
Enter "DHCP Setup" and select "Device IP Address" (default 192.168.1.1). Active "DHCP Server" and determine the range: "Range Start (Example 192.168.1.100)" and "Range End" (example 192.168.1.200) (note: don't use 192.168.1.1 or 192.168.1.255 into the range) and set "DNS Server/Use DNS as Bellow and set manually your DNS (example 8.8.8.8 8.8.4.4) and save the changes. Finally check "DHCP Status" ip leases your local network.
Enter a "system management" and select "Load Balance" (Auto Mode)
Enter "Setup/Network" and select "IPv4 Only" and "WAN Setting Table" should be "WAN1 (and WAN2) Obtain an IP automatically"
In "Setup / Advanced Routing" select "Gateway"
Note: Don't use "Router" because need to set routing table and RIP.
- Check "System Summary" that all information is correct
In this cisco url, explain how to configure in gateway and router mode in cisco RV320
Basic:
The external cable (ISP) must be connected to the Internet WAN port and cable to your local network must be connected to any of the LAN ports (1,2,3,4)
Enter Cisco RV320 (192.168.1.1). (Change default credentials)
Enter "DHCP Setup" and select "Device IP Address" (default 192.168.1.1). Active "DHCP Server" and determine the range: "Range Start (Example 192.168.1.100)" and "Range End" (example 192.168.1.200) (note: don't use 192.168.1.1 or 192.168.1.255 into the range) and set "DNS Server/Use DNS as Bellow and set manually your DNS (example 8.8.8.8 8.8.4.4) and save the changes. Finally check "DHCP Status" ip leases your local network.
Enter a "system management" and select "Load Balance" (Auto Mode)
Enter "Setup/Network" and select "IPv4 Only" and "WAN Setting Table" should be "WAN1 (and WAN2) Obtain an IP automatically"
In "Setup / Advanced Routing" select "Gateway"
Note: Don't use "Router" because need to set routing table and RIP.
- Check "System Summary" that all information is correct
edited Aug 4 '16 at 17:07
answered Aug 3 '16 at 21:24
user584517
External links can break or be unavailable, in which case your answer would not be useful. Please include the essential information within your answer and use the link for attribution and further reading. Thanks.
– fixer1234
Aug 3 '16 at 21:55
add a comment |
External links can break or be unavailable, in which case your answer would not be useful. Please include the essential information within your answer and use the link for attribution and further reading. Thanks.
– fixer1234
Aug 3 '16 at 21:55
External links can break or be unavailable, in which case your answer would not be useful. Please include the essential information within your answer and use the link for attribution and further reading. Thanks.
– fixer1234
Aug 3 '16 at 21:55
External links can break or be unavailable, in which case your answer would not be useful. Please include the essential information within your answer and use the link for attribution and further reading. Thanks.
– fixer1234
Aug 3 '16 at 21:55
add a comment |
Thanks for contributing an answer to Super User!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fsuperuser.com%2fquestions%2f891764%2fcisco-rv320-in-router-mode-loses-internet-connectivity%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
