How to fix Y layer shift on Creality Ender 3?
While printing a simple model, my printer starts to layer-shift the build in a direction suddenly. I used the default setting for ultimaker Cura 3.4.1. It has done this same thing for multiple different prints. I would guess it is the software.
How do I fix the issue?
cura ender-3 ultimaker
edited Dec 19 at 11:10
0scar
9,25921241
asked Dec 18 at 19:57
brocket12
61
New contributor
brocket12 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
While printing a simple model, my printer starts to layer-shift the build in a direction suddenly. I used the default setting for ultimaker Cura 3.4.1. It has done this same thing for multiple different prints. I would guess it is the software.
How do I fix the issue?
cura ender-3 ultimaker
edited Dec 19 at 11:10
0scar
9,25921241
asked Dec 18 at 19:57
brocket12
61
New contributor
brocket12 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
Terminology: that is not offset, that is layer shift
– Trish
Dec 18 at 20:11
Please specify if it is X or Y, it is clearly not both as shown in the image. Considering the markings on the bed, this appears to be a Y axis layer shift. Please acknowledge!
– 0scar
Dec 19 at 11:08
add a comment |
While printing a simple model, my printer starts to layer-shift the build in a direction suddenly. I used the default setting for ultimaker Cura 3.4.1. It has done this same thing for multiple different prints. I would guess it is the software.
How do I fix the issue?
cura ender-3 ultimaker
edited Dec 19 at 11:10
0scar
9,25921241
asked Dec 18 at 19:57
brocket12
61
New contributor
brocket12 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
While printing a simple model, my printer starts to layer-shift the build in a direction suddenly. I used the default setting for ultimaker Cura 3.4.1. It has done this same thing for multiple different prints. I would guess it is the software.
How do I fix the issue?
cura ender-3 ultimaker
cura ender-3 ultimaker
edited Dec 19 at 11:10
0scar
9,25921241
asked Dec 18 at 19:57
brocket12
61
New contributor
brocket12 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited Dec 19 at 11:10
0scar
9,25921241
asked Dec 18 at 19:57
brocket12
61
New contributor
brocket12 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited Dec 19 at 11:10
0scar
9,25921241
edited Dec 19 at 11:10
0scar
9,25921241
edited Dec 19 at 11:10
0scar
9,25921241
9,25921241
asked Dec 18 at 19:57
brocket12
61
New contributor
brocket12 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked Dec 18 at 19:57
brocket12
61
asked Dec 18 at 19:57
brocket12
61
61
New contributor
brocket12 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
brocket12 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
brocket12 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
Terminology: that is not offset, that is layer shift
– Trish
Dec 18 at 20:11
Please specify if it is X or Y, it is clearly not both as shown in the image. Considering the markings on the bed, this appears to be a Y axis layer shift. Please acknowledge!
– 0scar
Dec 19 at 11:08
add a comment |
Terminology: that is not offset, that is layer shift
– Trish
Dec 18 at 20:11
Please specify if it is X or Y, it is clearly not both as shown in the image. Considering the markings on the bed, this appears to be a Y axis layer shift. Please acknowledge!
– 0scar
Dec 19 at 11:08
Terminology: that is not offset, that is layer shift
– Trish
Dec 18 at 20:11
Terminology: that is not offset, that is layer shift
– Trish
Dec 18 at 20:11
Please specify if it is X or Y, it is clearly not both as shown in the image. Considering the markings on the bed, this appears to be a Y axis layer shift. Please acknowledge!
– 0scar
Dec 19 at 11:08
Please specify if it is X or Y, it is clearly not both as shown in the image. Considering the markings on the bed, this appears to be a Y axis layer shift. Please acknowledge!
– 0scar
Dec 19 at 11:08
add a comment |
2 Answers
2
active
oldest
votes
You have a case of layer shift. Layer shifts happened to me in 3 ways:
- The movement of the axis is hindered. Check if all cables run freely and without any chance to catch! improper cable chains can cause binding and stop the printhead or bed in movement and thus induce a shift.
- The acceleration might be too fast. Shift the acceleration of the printer movements down a notch. Don't print faster than ~60.
- The model might be broken. Re-slice the model just in case.
answered Dec 18 at 20:16
Trish
4,004635
add a comment |
In addition to the other answer to complete the overview, your stepper motor may not get enough power and misses steps, increasing the current by adjusting the stepper driver voltage could also solve the issue (when the current is too low that is! never just increase this to try out, you could damage the stepper, the drivers or the board, so beware).
answered Dec 18 at 22:08
0scar
9,25921241
add a comment |
Your Answer
StackExchange.ifUsing("editor", function () {
return StackExchange.using("mathjaxEditing", function () {
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["$", "$"], ["\\(","\\)"]]);
});
});
}, "mathjax-editing");
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "640"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
brocket12 is a new contributor. Be nice, and check out our Code of Conduct.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2f3dprinting.stackexchange.com%2fquestions%2f7699%2fhow-to-fix-y-layer-shift-on-creality-ender-3%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
You have a case of layer shift. Layer shifts happened to me in 3 ways:
- The movement of the axis is hindered. Check if all cables run freely and without any chance to catch! improper cable chains can cause binding and stop the printhead or bed in movement and thus induce a shift.
- The acceleration might be too fast. Shift the acceleration of the printer movements down a notch. Don't print faster than ~60.
- The model might be broken. Re-slice the model just in case.
answered Dec 18 at 20:16
Trish
4,004635
add a comment |
You have a case of layer shift. Layer shifts happened to me in 3 ways:
- The movement of the axis is hindered. Check if all cables run freely and without any chance to catch! improper cable chains can cause binding and stop the printhead or bed in movement and thus induce a shift.
- The acceleration might be too fast. Shift the acceleration of the printer movements down a notch. Don't print faster than ~60.
- The model might be broken. Re-slice the model just in case.
answered Dec 18 at 20:16
Trish
4,004635
add a comment |
You have a case of layer shift. Layer shifts happened to me in 3 ways:
- The movement of the axis is hindered. Check if all cables run freely and without any chance to catch! improper cable chains can cause binding and stop the printhead or bed in movement and thus induce a shift.
- The acceleration might be too fast. Shift the acceleration of the printer movements down a notch. Don't print faster than ~60.
- The model might be broken. Re-slice the model just in case.
answered Dec 18 at 20:16
Trish
4,004635
You have a case of layer shift. Layer shifts happened to me in 3 ways:
- The movement of the axis is hindered. Check if all cables run freely and without any chance to catch! improper cable chains can cause binding and stop the printhead or bed in movement and thus induce a shift.
- The acceleration might be too fast. Shift the acceleration of the printer movements down a notch. Don't print faster than ~60.
- The model might be broken. Re-slice the model just in case.
answered Dec 18 at 20:16
Trish
4,004635
edited Dec 19 at 10:12
answered Dec 18 at 20:16
Trish
4,004635
answered Dec 18 at 20:16
Trish
4,004635
answered Dec 18 at 20:16
Trish
4,004635
4,004635
add a comment |
add a comment |
In addition to the other answer to complete the overview, your stepper motor may not get enough power and misses steps, increasing the current by adjusting the stepper driver voltage could also solve the issue (when the current is too low that is! never just increase this to try out, you could damage the stepper, the drivers or the board, so beware).
answered Dec 18 at 22:08
0scar
9,25921241
add a comment |
In addition to the other answer to complete the overview, your stepper motor may not get enough power and misses steps, increasing the current by adjusting the stepper driver voltage could also solve the issue (when the current is too low that is! never just increase this to try out, you could damage the stepper, the drivers or the board, so beware).
answered Dec 18 at 22:08
0scar
9,25921241
add a comment |
In addition to the other answer to complete the overview, your stepper motor may not get enough power and misses steps, increasing the current by adjusting the stepper driver voltage could also solve the issue (when the current is too low that is! never just increase this to try out, you could damage the stepper, the drivers or the board, so beware).
answered Dec 18 at 22:08
0scar
9,25921241
In addition to the other answer to complete the overview, your stepper motor may not get enough power and misses steps, increasing the current by adjusting the stepper driver voltage could also solve the issue (when the current is too low that is! never just increase this to try out, you could damage the stepper, the drivers or the board, so beware).
answered Dec 18 at 22:08
0scar
9,25921241
answered Dec 18 at 22:08
0scar
9,25921241
answered Dec 18 at 22:08
0scar
9,25921241
answered Dec 18 at 22:08
0scar
9,25921241
9,25921241
add a comment |
add a comment |
brocket12 is a new contributor. Be nice, and check out our Code of Conduct.
brocket12 is a new contributor. Be nice, and check out our Code of Conduct.
brocket12 is a new contributor. Be nice, and check out our Code of Conduct.
brocket12 is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to 3D Printing Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2f3dprinting.stackexchange.com%2fquestions%2f7699%2fhow-to-fix-y-layer-shift-on-creality-ender-3%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Terminology: that is not offset, that is layer shift
– Trish
Dec 18 at 20:11
Please specify if it is X or Y, it is clearly not both as shown in the image. Considering the markings on the bed, this appears to be a Y axis layer shift. Please acknowledge!
– 0scar
Dec 19 at 11:08