Cause of triode mode in MOSFET
My reference text introduces the MOFSET as follows:
The text says the induced channel has uniform width as long as $v_{DS}$ is small, because in that case $v_{GD} = v_{GS} - v_{DS} approx v_{GS}$, and if this is violated, then the width of the channel near the drain decreases. I don't really understand why, nor how this is relevant to the width of the channel. Shouldn't $v_{DS}$ be uniform across the drain? Then wouldn't all components of the electric field be horizontal?
voltage transistors mosfet semiconductors
asked 2 days ago
jeanluc
1202
add a comment |
My reference text introduces the MOFSET as follows:
The text says the induced channel has uniform width as long as $v_{DS}$ is small, because in that case $v_{GD} = v_{GS} - v_{DS} approx v_{GS}$, and if this is violated, then the width of the channel near the drain decreases. I don't really understand why, nor how this is relevant to the width of the channel. Shouldn't $v_{DS}$ be uniform across the drain? Then wouldn't all components of the electric field be horizontal?
voltage transistors mosfet semiconductors
asked 2 days ago
jeanluc
1202
1
Read this ittc.ku.edu/~jstiles/312/handouts/… (page 5,6 ). And this also can help ittc.ku.edu/~jstiles/312/handouts/…
– G36
2 days ago
add a comment |
My reference text introduces the MOFSET as follows:
The text says the induced channel has uniform width as long as $v_{DS}$ is small, because in that case $v_{GD} = v_{GS} - v_{DS} approx v_{GS}$, and if this is violated, then the width of the channel near the drain decreases. I don't really understand why, nor how this is relevant to the width of the channel. Shouldn't $v_{DS}$ be uniform across the drain? Then wouldn't all components of the electric field be horizontal?
voltage transistors mosfet semiconductors
asked 2 days ago
jeanluc
1202
My reference text introduces the MOFSET as follows:
The text says the induced channel has uniform width as long as $v_{DS}$ is small, because in that case $v_{GD} = v_{GS} - v_{DS} approx v_{GS}$, and if this is violated, then the width of the channel near the drain decreases. I don't really understand why, nor how this is relevant to the width of the channel. Shouldn't $v_{DS}$ be uniform across the drain? Then wouldn't all components of the electric field be horizontal?
voltage transistors mosfet semiconductors
voltage transistors mosfet semiconductors
asked 2 days ago
jeanluc
1202
asked 2 days ago
jeanluc
1202
asked 2 days ago
jeanluc
1202
asked 2 days ago
jeanluc
1202
asked 2 days ago
jeanluc
1202
1202
1
Read this ittc.ku.edu/~jstiles/312/handouts/… (page 5,6 ). And this also can help ittc.ku.edu/~jstiles/312/handouts/…
– G36
2 days ago
add a comment |
1
Read this ittc.ku.edu/~jstiles/312/handouts/… (page 5,6 ). And this also can help ittc.ku.edu/~jstiles/312/handouts/…
– G36
2 days ago
1
1
Read this ittc.ku.edu/~jstiles/312/handouts/… (page 5,6 ). And this also can help ittc.ku.edu/~jstiles/312/handouts/…
– G36
2 days ago
Read this ittc.ku.edu/~jstiles/312/handouts/… (page 5,6 ). And this also can help ittc.ku.edu/~jstiles/312/handouts/…
– G36
2 days ago
add a comment |
2 Answers
2
active
oldest
votes
The width of the conducting channel at any point is a function of the voltage between that point in the channel and the gate.
If Vds is zero, source and drain are at the same potential. So the potential at each point across the channel will also be the same (zero). The channel has constant width.
If Vds is (say) 1V, now there is a 1V potential distribution across the channel. Now the potential between gate and each point in the channel is not equal - it decreases as you get closer to the more positive end (drain). Let's say Vgs = 5V - that means that Vgd would be only 4V.
Hence the width of the conducting channel will decrease. This is what they are showing in the figure.
answered 2 days ago
dmb
1,455412
add a comment |
The triode, or ohmic region, is a function of both forward, $I_F$, and reverse, $I_R$, currents. The capacitance in the channel is an approximation, as you have a varying capacitance per unit area; however, we pretty much just use
$$Cequiv(C_{ox}+C_{dep})=frac{partial Q_m}{partial psi_s}$$
If the magnitudes of $I_F$ and $I_R$ are comparable, then the channel current depends strongly both on the source voltage and on the drain voltage. In this case, the transistor is in the ohmic region. Using the approximations made my Mary Ann Maher and Carver Mead, we can say that
$$I=I_F-I_R=frac{Smu}{2C}left(Q_S^2-2CU_TQ_Sright)-frac{Smu}{2C}left(Q_D^2-2CU_TQ_Dright)$$
If the forward current component is much larger than the reverse current component, then the channel current no longer depends significantly on the drain voltage
and the transistor is saturated.
As an aside, I dislike that picture because you'll never form a complete channel unless you overdrive the gate, this is why "pinch off" occurs. The most succinct discussions on the behavior of MOSFET devices are from Andy Grove, Mary Maher or Carver Mead.
answered 2 days ago
b degnan
2,0811622
add a comment |
Your Answer
StackExchange.ifUsing("editor", function () {
return StackExchange.using("mathjaxEditing", function () {
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
});
});
}, "mathjax-editing");
StackExchange.ifUsing("editor", function () {
return StackExchange.using("schematics", function () {
StackExchange.schematics.init();
});
}, "cicuitlab");
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "135"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f414271%2fcause-of-triode-mode-in-mosfet%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
The width of the conducting channel at any point is a function of the voltage between that point in the channel and the gate.
If Vds is zero, source and drain are at the same potential. So the potential at each point across the channel will also be the same (zero). The channel has constant width.
If Vds is (say) 1V, now there is a 1V potential distribution across the channel. Now the potential between gate and each point in the channel is not equal - it decreases as you get closer to the more positive end (drain). Let's say Vgs = 5V - that means that Vgd would be only 4V.
Hence the width of the conducting channel will decrease. This is what they are showing in the figure.
answered 2 days ago
dmb
1,455412
add a comment |
The width of the conducting channel at any point is a function of the voltage between that point in the channel and the gate.
If Vds is zero, source and drain are at the same potential. So the potential at each point across the channel will also be the same (zero). The channel has constant width.
If Vds is (say) 1V, now there is a 1V potential distribution across the channel. Now the potential between gate and each point in the channel is not equal - it decreases as you get closer to the more positive end (drain). Let's say Vgs = 5V - that means that Vgd would be only 4V.
Hence the width of the conducting channel will decrease. This is what they are showing in the figure.
answered 2 days ago
dmb
1,455412
add a comment |
The width of the conducting channel at any point is a function of the voltage between that point in the channel and the gate.
If Vds is zero, source and drain are at the same potential. So the potential at each point across the channel will also be the same (zero). The channel has constant width.
If Vds is (say) 1V, now there is a 1V potential distribution across the channel. Now the potential between gate and each point in the channel is not equal - it decreases as you get closer to the more positive end (drain). Let's say Vgs = 5V - that means that Vgd would be only 4V.
Hence the width of the conducting channel will decrease. This is what they are showing in the figure.
answered 2 days ago
dmb
1,455412
The width of the conducting channel at any point is a function of the voltage between that point in the channel and the gate.
If Vds is zero, source and drain are at the same potential. So the potential at each point across the channel will also be the same (zero). The channel has constant width.
If Vds is (say) 1V, now there is a 1V potential distribution across the channel. Now the potential between gate and each point in the channel is not equal - it decreases as you get closer to the more positive end (drain). Let's say Vgs = 5V - that means that Vgd would be only 4V.
Hence the width of the conducting channel will decrease. This is what they are showing in the figure.
answered 2 days ago
dmb
1,455412
answered 2 days ago
dmb
1,455412
answered 2 days ago
dmb
1,455412
answered 2 days ago
dmb
1,455412
1,455412
add a comment |
add a comment |
The triode, or ohmic region, is a function of both forward, $I_F$, and reverse, $I_R$, currents. The capacitance in the channel is an approximation, as you have a varying capacitance per unit area; however, we pretty much just use
$$Cequiv(C_{ox}+C_{dep})=frac{partial Q_m}{partial psi_s}$$
If the magnitudes of $I_F$ and $I_R$ are comparable, then the channel current depends strongly both on the source voltage and on the drain voltage. In this case, the transistor is in the ohmic region. Using the approximations made my Mary Ann Maher and Carver Mead, we can say that
$$I=I_F-I_R=frac{Smu}{2C}left(Q_S^2-2CU_TQ_Sright)-frac{Smu}{2C}left(Q_D^2-2CU_TQ_Dright)$$
If the forward current component is much larger than the reverse current component, then the channel current no longer depends significantly on the drain voltage
and the transistor is saturated.
As an aside, I dislike that picture because you'll never form a complete channel unless you overdrive the gate, this is why "pinch off" occurs. The most succinct discussions on the behavior of MOSFET devices are from Andy Grove, Mary Maher or Carver Mead.
answered 2 days ago
b degnan
2,0811622
add a comment |
The triode, or ohmic region, is a function of both forward, $I_F$, and reverse, $I_R$, currents. The capacitance in the channel is an approximation, as you have a varying capacitance per unit area; however, we pretty much just use
$$Cequiv(C_{ox}+C_{dep})=frac{partial Q_m}{partial psi_s}$$
If the magnitudes of $I_F$ and $I_R$ are comparable, then the channel current depends strongly both on the source voltage and on the drain voltage. In this case, the transistor is in the ohmic region. Using the approximations made my Mary Ann Maher and Carver Mead, we can say that
$$I=I_F-I_R=frac{Smu}{2C}left(Q_S^2-2CU_TQ_Sright)-frac{Smu}{2C}left(Q_D^2-2CU_TQ_Dright)$$
If the forward current component is much larger than the reverse current component, then the channel current no longer depends significantly on the drain voltage
and the transistor is saturated.
As an aside, I dislike that picture because you'll never form a complete channel unless you overdrive the gate, this is why "pinch off" occurs. The most succinct discussions on the behavior of MOSFET devices are from Andy Grove, Mary Maher or Carver Mead.
answered 2 days ago
b degnan
2,0811622
add a comment |
The triode, or ohmic region, is a function of both forward, $I_F$, and reverse, $I_R$, currents. The capacitance in the channel is an approximation, as you have a varying capacitance per unit area; however, we pretty much just use
$$Cequiv(C_{ox}+C_{dep})=frac{partial Q_m}{partial psi_s}$$
If the magnitudes of $I_F$ and $I_R$ are comparable, then the channel current depends strongly both on the source voltage and on the drain voltage. In this case, the transistor is in the ohmic region. Using the approximations made my Mary Ann Maher and Carver Mead, we can say that
$$I=I_F-I_R=frac{Smu}{2C}left(Q_S^2-2CU_TQ_Sright)-frac{Smu}{2C}left(Q_D^2-2CU_TQ_Dright)$$
If the forward current component is much larger than the reverse current component, then the channel current no longer depends significantly on the drain voltage
and the transistor is saturated.
As an aside, I dislike that picture because you'll never form a complete channel unless you overdrive the gate, this is why "pinch off" occurs. The most succinct discussions on the behavior of MOSFET devices are from Andy Grove, Mary Maher or Carver Mead.
answered 2 days ago
b degnan
2,0811622
The triode, or ohmic region, is a function of both forward, $I_F$, and reverse, $I_R$, currents. The capacitance in the channel is an approximation, as you have a varying capacitance per unit area; however, we pretty much just use
$$Cequiv(C_{ox}+C_{dep})=frac{partial Q_m}{partial psi_s}$$
If the magnitudes of $I_F$ and $I_R$ are comparable, then the channel current depends strongly both on the source voltage and on the drain voltage. In this case, the transistor is in the ohmic region. Using the approximations made my Mary Ann Maher and Carver Mead, we can say that
$$I=I_F-I_R=frac{Smu}{2C}left(Q_S^2-2CU_TQ_Sright)-frac{Smu}{2C}left(Q_D^2-2CU_TQ_Dright)$$
If the forward current component is much larger than the reverse current component, then the channel current no longer depends significantly on the drain voltage
and the transistor is saturated.
As an aside, I dislike that picture because you'll never form a complete channel unless you overdrive the gate, this is why "pinch off" occurs. The most succinct discussions on the behavior of MOSFET devices are from Andy Grove, Mary Maher or Carver Mead.
answered 2 days ago
b degnan
2,0811622
edited 2 days ago
answered 2 days ago
b degnan
2,0811622
answered 2 days ago
b degnan
2,0811622
answered 2 days ago
b degnan
2,0811622
2,0811622
add a comment |
add a comment |
Thanks for contributing an answer to Electrical Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f414271%2fcause-of-triode-mode-in-mosfet%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
1
Read this ittc.ku.edu/~jstiles/312/handouts/… (page 5,6 ). And this also can help ittc.ku.edu/~jstiles/312/handouts/…
– G36
2 days ago